Inappropriate drivers can also cause Audacity to crash during playback or recording, without necessarily crashing the computer. Even if the problem occurs after updating to the latest Audacity version, it still is not Audacity's direct fault because Audacity does not have kernel privileges to make the computer restart. It happens when your computer sound device has a bad or mismatched driver or there is a problem with a system driver that interacts with that sound device. Why does the computer reboot or show a blue screen message when I launch Audacity or play or record? The recording device message most commonly occurs on Windows when one of the sound device inputs is not properly enabled or otherwise cannot respond to Audacity's request to start recording.įor details of how to fix this please see Error opening sound device. For example you will see this error if you attempt to Record to more channels than your device supports, or if you try to overdub on a device that can either record or play back but not both. These messages can suggest a problem with the drivers of the sound device, or possibly that you are asking the device to do something it cannot do. this is a generic message that is associated with a failure to start the audio playback stream. Error opening recording device - Error code -xxxx this means there is a problem with your Audacity, operating system or sound device recording settings, where xxxx is replaced by a numeric code see here for details.If the message mentions "playback device", it means there is a problem with your playback settings. If the message mentions "recording device", it means there's a problem with your Audacity, operating system or sound device recording settings. These error messages ask you to check the recording or playback device settings and the Audacity project sample rate. Try installing a different Software driver.Why do I get "Error opening sound device" or "Error opening recording device"?.Reboot your computer and/or start with a new Audacity project and a fresh recording.Also, check that all of your settings in Audacity and in the Sound Control Panel are either mono (1-channel) or stereo (2-channels). Playback Tab > Select the M-Audio unit Properties Listen > Turn OFF Listen to this device Advanced: Default Format to project rate. Start Windows Sound Control Panel: Windows-Key, “R”, “mmsys.cpl” (or Windows > Settings > System > Sound > Sound Control Panel). 44100Hz: Set the Audacity Project Rate to 44100Hz (lower left corner). Set everything to the same sample rate, e.g.You may find you are unable to overdub with your headphones plugged into the M-Audio. You wouldn’t be the first person to have issues with trying to overdub with the M-Track M-Audio.įirst, see if you can overdub with your headphones plugged into the computer instead of the microphone. And just to make it interesting, two tracks did record once or twice, particularly when I Zoomed with a friend to get help and tried it to show him, and of course both tracks worked fine, but not since.Īny help with this would be appreciated. I recorded multiple tracks for years, then I didn’t record over Christmas (and there have been Windows updates). I have gone into my Windows Settings-Sound-Sound Control Panel-Recording and enabled ‘Stereo Mix’, as well as my interface. I do not have Skype opening in my Startup. Just little flash of mic symbol and then nothing - no recording.īut my recording device is available for the first track, and appears to be very briefly available for the second. Both appear briefly and then are gone, and sometimes I get the error message:Įrror Codes: -9985 Device Unavailable”, n sometimes I don’t get an error message. The Audacity monitor works fine with my mic, so it is picking up the signal from my mic and interface (M-Audio 192/6).īut when I try to record on the second track, the little mic symbol on the task bar, which indicates Audacity is receiving from my mic, appears for about a second, and then it disappears, as do the lines around the red record button that indicate recording. I can only get I track per project to record. Or if I create a rhythm track, it works fine, but I can’t get a second track to record. When I create a second track and try to record it doesn’t work. When creating and recording on the first track in a project, everything works fine.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |